Oregon DMV CDL General Knowledge Practice Test 6
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. How does Oregon's CDL manual define texting for a commercial motor vehicle driver?
Show answer
Answer C: Manually entering text into, or reading text from, a device
Oregon's CDL manual defines texting broadly as manually entering text into, or reading text from, a phone, computer, or other device used to enter, write, send, receive, or read text.
-
2. Why does a heavy vehicle need a much larger gap than a car in order to cross or enter traffic?
Show answer
Answer C: Because it accelerates slowly and needs far more road and time to clear the intersection
Slow acceleration combined with the length of the vehicle means a gap that would feel comfortable in a car is nowhere near enough.
-
3. At the scale your tractor drive axles are overweight while the trailer axles have room. Sliding the trailer tandems forward will do what?
Show answer
Answer C: Move weight off the drive axles and onto the trailer axles
Sliding the trailer tandems forward brings the rear support closer to the load, so the trailer axles pick up more weight and the drive axles carry less; sliding them rearward does the opposite.
-
4. You find a defect during the pre-trip inspection. What must happen before the vehicle is driven?
Show answer
Answer C: It must be repaired, or the vehicle must not be driven
Writing a defect down does not make the vehicle safe; a defect that affects safe operation has to be corrected before the trip starts.
-
5. An angry driver has cut in front of you and is now braking hard to provoke you. What is the safest response?
Show answer
Answer D: Drop back, avoid eye contact and let the driver go
Giving an aggressive driver space and no response removes the conflict, while any answering gesture invites escalation you cannot control in a heavy vehicle.
-
6. On a scale, your loaded truck is well under the gross weight limit, but one axle is above the limit for that axle. What does this mean?
Show answer
Answer D: The vehicle is overloaded and the load must be shifted or reduced before you drive on
Each axle and axle group has its own limit and each must be respected; being under the gross limit does not excuse an overloaded axle.
-
7. A commercial driver is convicted of two serious traffic violations within three years. What is the result?
Show answer
Answer D: Disqualification for 60 days
Two serious traffic violations in a three year period bring a 60 day disqualification, and a third in the same period raises it to 120 days.
-
8. Why does a load need to be balanced from side to side?
Show answer
Answer B: Because a heavy side raises the rollover risk and can overload the tires and springs on that side
An uneven load tips the balance of the vehicle in curves and pushes the tires and suspension on the loaded side past their rating.
-
9. What is the best practice when fog is thick enough to hide the road ahead?
Show answer
Answer B: Slow down before entering the fog, and if visibility is too poor, pull off into a rest area or truck stop until it improves
The safest choice in heavy fog is not to be driving in it, and if you are already in it your speed has to come down before your visibility does.
-
10. When must a post-trip inspection be made?
Show answer
Answer D: At the end of each day the driver operates the vehicle
The post-trip inspection closes out each driving day so that anything found is recorded before the vehicle is handed to the next driver.
-
11. A roadside test shows a commercial driver has measurable alcohol in the system but below 0.04. What happens?
Show answer
Answer C: The driver is placed out of service for 24 hours
Any measurable alcohol while on duty results in an immediate 24 hour out of service order, even when the concentration is under the 0.04 limit.
-
12. Your brakes have failed on a downgrade and there is no escape ramp in sight. What is the best choice?
Show answer
Answer A: Steer into an open field or onto a side road that flattens out or climbs uphill
A flat or uphill escape route uses gravity and rolling resistance to stop the vehicle; take it as soon as you see it, because the longer you wait the faster you go.
-
13. What blood alcohol concentration makes it illegal to operate a commercial motor vehicle under Oregon's CDL rules?
Show answer
Answer D: 0.04 percent or more
Oregon's Commercial Driver Manual sets the illegal threshold for operating a CMV at a blood alcohol concentration of 0.04 percent or more.
-
14. When should a driver select the gear for a long, steep downgrade?
Show answer
Answer B: Before starting down the grade
The low gear has to be chosen before the descent, because a heavy vehicle gaining speed may refuse to shift down at all.
-
15. You pick up a sealed trailer at a shipper. What should you check before leaving the dock?
Show answer
Answer B: That the seal number matches the paperwork and that the doors are properly closed
You cannot look at a sealed load, but you can confirm that the seal is intact, that its number matches the documents and that the doors are secure.
-
16. Apart from the risk of stalling, why is rolling backwards when starting on an upgrade so serious in a heavy vehicle?
Show answer
Answer D: You can strike the vehicle behind you, which is often much closer than you think
You cannot see how close the vehicle behind has stopped, and even a short roll back is enough to hit it.
-
17. The brake pedal goes to the floor in a vehicle with hydraulic brakes. What can you do to build some braking pressure?
Show answer
Answer B: Pump the brake pedal rapidly, which may bring back enough pressure to slow the vehicle
Pumping can restore some hydraulic pressure; along with downshifting and the parking brake it is one of the ways to stop when the pedal fails.
-
18. Why must you never coast down a hill in neutral or with the clutch pushed in?
Show answer
Answer C: You lose the braking effect of the engine and your brakes may overheat and fail
Engine braking is what keeps a heavy vehicle in check on a grade; coasting throws it away and leaves the service brakes to do all the work until they overheat.
-
19. Federal rules require a power unit that is not carrying placarded hazardous materials to have a fire extinguisher with which minimum rating?
Show answer
Answer A: One rated 5 B:C or more, or two rated 4 B:C or more each
The minimum is a single unit rated 5 B:C or more, or two units of at least 4 B:C each, which is enough to attack a fuel or electrical fire.
-
20. Besides allowing the move at all, what does an oversize load permit usually set out?
Show answer
Answer C: The route to be followed, the hours of travel allowed and the warning equipment needed
Permits for oversize movements normally name the roads that may be used, restrict the times of travel, and list the flags, signs and escorts required.
-
21. You are stopped in traffic on a steep upgrade behind another truck. How much space should you leave in front?
Show answer
Answer A: Enough that you can pull away without rolling back into the vehicle behind you
Room ahead lets you get moving smoothly on a grade instead of having to hold the vehicle perfectly still or roll back toward the traffic behind.
-
22. Where are the OVERSIZE LOAD signs normally carried on a vehicle moving under such a permit?
Show answer
Answer A: On the front and the rear of the vehicle
The warning signs face the traffic that meets the load and the traffic that comes up behind it, so they go on the front and the rear.
-
23. What is the most common cause of a front-wheel skid, where the vehicle keeps going straight even though you turn the wheel?
Show answer
Answer B: Driving too fast for the conditions
A front-wheel skid usually comes from too much speed for the traction available; the only cure is to let the vehicle slow down and stop turning or braking so hard.
-
24. Which lamp must make the rear registration plate legible after dark?
Show answer
Answer C: A white lamp that lights the plate
A white license plate lamp is required so the plate can be read at night, and a burned out one is a defect like any other lamp.
-
25. You are loading a flatbed that has no sides or bulkheads. How must the cargo be held?
Show answer
Answer D: By tiedowns, blocking or bracing, since there are no walls to keep it from shifting or falling off
Open decks depend entirely on securement devices; every article must be tied down or otherwise immobilized so it cannot move, spill or fall.
-
26. A straight truck has a long body behind the rear axle. What happens to that overhang in a sharp left turn?
Show answer
Answer D: It swings out to the right and can strike a vehicle or an object on that side
Body that hangs behind the rear axle swings the opposite way to the turn, so the tail of the truck sweeps out into the next lane or over the curb.
-
27. Cargo securement must be strong enough to hold the load under which conditions?
Show answer
Answer A: Hard braking, hard acceleration and hard turning, as well as the bouncing of the road
The securement standard is written around the forces of a hard stop, a hard start, a hard turn and vertical movement on a rough surface, all of which occur in ordinary driving.
-
28. Under federal rules, which commercial vehicles must stop at every railroad crossing before proceeding?
Show answer
Answer D: Passenger buses and placarded hazardous materials vehicles
Buses carrying passengers and vehicles required to display hazardous materials placards must stop at crossings, while other commercial vehicles slow and check.
-
29. How soon must warning devices be placed after a commercial vehicle stops on the traveled part or the shoulder of a highway?
Show answer
Answer D: As soon as possible and in any case within 10 minutes
The hazard warning flashers go on immediately and the warning devices must be in place as soon as possible, never later than 10 minutes after stopping.
-
30. During the vehicle overview, what should the driver look for on the ground under the vehicle?
Show answer
Answer B: Fresh puddles of oil, coolant, grease or fuel
New stains on the ground are the earliest sign of a leak, so the overview includes a look underneath before anything is opened or started.
-
31. Your vehicle begins to hydroplane on a wet road. What should you do?
Show answer
Answer B: Release the accelerator and push in the clutch so the wheels can turn freely and regain grip
Hydroplaning tires are riding on water; slowing without braking lets them settle back onto the road and grip again.
-
32. If a CDL holder's alcohol-related offense occurs while operating a CMV placarded for hazardous materials in Oregon, the minimum disqualification period increases to what?
Show answer
Answer C: 3 years
Oregon's CDL manual raises the minimum disqualification from one year to three years when a qualifying alcohol or drug offense occurs while the CMV is placarded for hazardous materials.
-
33. How is a shipping container normally secured when it is carried on a special container chassis?
Show answer
Answer B: With its own locking devices that attach the container directly to the chassis frame
Containers built for rail or ship transport have locking corners that fasten to a matching chassis; a container carried on a plain flatbed must be secured like any other cargo.
-
34. Under federal rules, what is required of a commercial driver who wants to use a mobile phone while driving?
Show answer
Answer B: The phone must be hands-free and started with no more than a single button press, and it must not be held
Federal rules ban texting and hand-held phone use while driving a commercial vehicle; reaching for, holding or dialing a phone is a violation.
-
35. What is a bulkhead in a cargo body used for?
Show answer
Answer D: To divide the space and stop cargo from moving into another part of the body
A bulkhead is a solid partition that separates one part of the load space from another and blocks the cargo from moving past it.
-
36. What frame defects are you looking for during the walkaround?
Show answer
Answer A: Cracks, bends or broken cross members
The frame carries the whole load, so cracked or bent rails and broken cross members are serious structural defects.
-
37. Two vehicles of exactly the same length make a right turn, one gently and one very tightly. What is the effect on off-tracking?
Show answer
Answer A: Turning more sharply increases off-tracking, so the tight turn needs more room
Off-tracking depends on both the length of the vehicle and the sharpness of the turn; a tighter corner brings the rear wheels further inside the path of the front wheels.
-
38. Why must the downshift be finished before you reach a steep downgrade or a sharp curve rather than during it?
Show answer
Answer D: Because once your speed is too high you may not get into any gear at all
If you wait until speed has built up, the lower gear may refuse to engage and you can be left in neutral with no engine braking at all.
-
39. What must be true of the person who performs the annual periodic inspection?
Show answer
Answer D: They must meet the federal qualification requirements for an inspector
The inspection has to be done by someone who meets the federal training and experience requirements for inspectors, whoever employs them.
-
40. What should a driver assume about the height posted at a bridge or an overpass?
Show answer
Answer B: That it may be wrong, because repaving or packed snow can leave less clearance than the sign shows
Resurfacing and packed snow raise the road under the structure, so the real clearance can be lower than the posted figure.
-
41. What does the commercial driver manual tell you to do with the parking brake when you leave your vehicle?
Show answer
Answer B: Apply the parking brake every time you leave the vehicle
The manual is explicit that the parking brake goes on whenever the driver leaves the vehicle, because once nobody is at the controls it is the only thing holding it.
-
42. When should a driver add space beyond the basic following distance rule?
Show answer
Answer D: On slippery roads and whenever visibility is poor
The seconds rule is a minimum for good conditions, so rain, snow, darkness and heavy traffic all call for more space than that.
-
43. Before starting a trip, what must the driver confirm about the weight of the loaded vehicle?
Show answer
Answer A: That it is within the legal gross and axle limits for the route being driven
Overweight vehicles brake poorly, damage tires and suspension components, and can be put out of service at a scale, so weight is checked before the wheels turn.
-
44. Your load projects more than 4 feet beyond the rear of the vehicle. How must the projecting end be marked?
Show answer
Answer A: With a red or orange flag by day and a red lamp after dark
Federal rules require a warning flag on a rear projecting load in daylight and a red lamp on the end of it when lights are required.
-
45. Under Oregon's CDL rules, exceeding the posted speed limit by how much while operating a commercial motor vehicle counts as a serious traffic violation?
Show answer
Answer B: 15 miles per hour or more
Oregon's Commercial Driver Manual defines excessive speeding of 15 mph or more above the posted limit as a serious traffic violation for CDL purposes.
-
46. An unblocked crate 4 feet long and weighing 900 pounds needs at least how many tiedowns?
Show answer
Answer D: One
An article 5 feet or less in length and 1,100 pounds or less in weight is covered by a minimum of one tiedown.
-
47. Which exhaust system condition must be reported as a defect?
Show answer
Answer B: A section repaired by wrapping tape or patching material around the pipe
Exhaust parts may not be patched with wrap or tape, because the repair does not contain the gas or the heat and it fails quickly in service.
-
48. Where should a trailer be dropped, and what else does the driver do before pulling out from under it?
Show answer
Answer C: On solid level ground, with the trailer wheels chocked if it may roll
A dropped trailer must sit on ground that will carry the landing gear without sinking, and chocks stop it rolling once the tractor and its air supply are gone.
-
49. Your vehicle stalls on a railroad crossing and a train is coming. What should you do?
Show answer
Answer C: Get out at once and move toward the train, well off to one side
Leave the vehicle immediately and move at an angle toward the oncoming train, so that wreckage thrown forward by the impact travels away from you.
-
50. Why should a driver avoid shifting gears in the middle of a turn at an intersection?
Show answer
Answer D: Shifting during the turn takes a hand off the wheel and can cost you control
Pick the gear before you begin turning; shifting in the turn removes a hand from the wheel and can interrupt power just when you need steady control.